A replacement bottle marked 500 mL can still be too tall for the bucket cover. To check centrifuge bottle rotor compatibility, find the manual entry for the rotor and holder installed in your centrifuge. Look for the specified bottle and closure or, where the manufacturer allows alternatives, the vessel dimensions and base shape it accepts.
The part number on the old bottle or its packaging helps identify what you’re replacing. Once you’ve matched the hardware, check that both the bottle and the equipment configuration support the relative centrifugal force (RCF) your method calls for.
Why Two 500 mL Bottles Can Fit Differently
If a bottle looks tight in its adapter, it’s tempting to choose the narrower model. Consider these two 500 mL flat-bottom polypropylene bottles with screw caps. The dimensions come from Kelabscience’s Centrifuge Bottles specification table.
| Kelabscience bottle | Inside mouth diameter (mm) | Body outside diameter (mm) | Height with cap (mm) |
|---|---|---|---|
| KL-CB-0500A | 52 | 72.5 | 154.5 |
| KL-CB-0500B | 37 | 69 | 167 |
The B bottle is 3.5 mm narrower across the body and 12.5 mm taller with its cap on. If the bucket cover already sits close to the original cap, that extra height could rule out the slimmer bottle.
Kelabscience lists dimensions for both bottles and asks users to confirm the rotor combination and applicable RCF for their particular setup.
Which Rotor, Bucket and Adapter Do You Have?
Look for the model marked on the rotor itself. A brochure entry such as “4 × 500 mL” tells you the number of positions and their nominal capacity. It leaves open which holder supports each bottle.
On a swinging-bucket rotor, record the bucket part number, any adapter or insert, and the bucket cover your procedure requires. Two different buckets can mount on the same rotor and have separate tables in the manual. A photo of the markings is useful when two sets of hardware look alike.
On a fixed-angle rotor, look up the cavity and any insert or bottle support specified for it. Keep those references with the centrifuge model so the equipment manufacturer can identify the full setup. The University of Texas at Austin also advises checking compatibility across these components in its centrifuge safety guidance.
Which Measurements on the Bottle Drawing Matter?
Put the bottle drawing beside the drawing of the holder and start at the base. A flat base and a conical tip sit differently in their supports. Even with the same overall bottle height, the caps can end up at different heights above the adapter.
The body outside diameter (OD) applies to the part of the bottle indicated by the dimension arrows. A shoulder, flange or cap rim may be wider. Find the maximum width with the cap fitted and where it occurs. A flange might have to pass through the adapter opening. For a cap that sits above the insert, the space under the bucket cover may matter more. The inside mouth diameter measures only the opening you pour through.
Read the capped height from the base to the highest point of the specified closure. If the drawing stops at the neck, ask for the assembled height. Likewise, if the supplier gives only a body OD, record the maximum width with the cap fitted as not specified until the supplier provides it.
When you’re comparing an unlisted bottle against a dimensional limit, check whether the drawing gives a nominal size or a maximum allowed size. A nominal width with a positive tolerance can describe bottles wider than the number printed beside the arrow.
How to Read One Row of a Rotor Compatibility Table
Page 80 of the Eppendorf Centrifuge 5910 R manual opens the table for an S-4×750 swing-bucket rotor fitted with four 750 mL round buckets. The 500 mL row is at the top of page 83. Farther down that page the manual switches to plate buckets for the same rotor.
The row pairs a 500 mL Corning conical vessel with adapter 5825 745.000. Its tube diameter field gives 96 mm for the listed vessel. The manual rules out the aerosol-tight bucket cap for this combination and lists a maximum tube length of 147 mm without that bucket cap. The bottle’s own screw cap is a separate closure.
This entry covers only the named Corning vessel and adapter. For either flat-bottom Kelabscience bottle, look for a separate manual entry or ask the equipment manufacturer for written confirmation covering your bottle and hardware. If your procedure requires a sealed bucket, include the required bucket cover in that check.
See Eppendorf, Centrifuge 5910 R, English original instructions, document 5942 900.025-02/082019, section 12.2.1, pp. 80–83. Use the edition that applies to your own equipment when looking up a replacement.
What If Your Bottle Is Missing From the Chart?
An unlisted part number is a reason to read the notes around the table. Does the manufacturer name one vessel, or does it explicitly accept other bottles meeting defined criteria? A bottle can sit neatly in a stationary bucket while its support under load is still an open question.
| What the documentation shows | How to use it |
|---|---|
| Exact combination listed. The entry covers your bottle and closure with the installed rotor, holder and any required adapter. | Follow the conditions in that entry. Check your intended RCF against both the bottle and equipment ratings. Keep the loaded mass within any limit the manual gives per bucket or per rotor bore. |
| Alternatives explicitly permitted. The manufacturer specifies which other vessels may be used. | Compare the capped-bottle drawing with every applicable criterion, including base shape, support and dimensional limits. Check the same operating limits once the criteria are satisfied. |
| A stated requirement conflicts. The entry calls for a different base shape or excludes a cover your procedure requires. | Set that combination aside and look for a documented setup that meets the requirement. |
| The evidence is incomplete. The row names another bottle, or a dimension is missing for a permitted alternative. | For a missing dimension, obtain it and recheck the criteria. If the entry covers only another vessel, seek written confirmation from the equipment manufacturer for your exact combination before use. |
Load and fill volume are easy to mix up on a request form. For the round bucket in the 5910 R example, page 80 counts the adapter, vessel and contents together as the load on one bucket. For a fixed-angle rotor, page 30 of the same manual specifies the load for each rotor bore. Record the fill volume in mL and the combined mass in grams, using the load definition for your rotor.
What to Send for a Compatibility Check
The bottle supplier can help if the drawing shows only the body. Send the bottle and screw-cap part numbers. Ask for a drawing of the assembled bottle showing the dimensions and tolerances you need, along with the bottle’s RCF rating under your proposed conditions.
The equipment manufacturer can check the rotor side of the question. Include the centrifuge and rotor models, the bottle drawing and part numbers for the accessories you use, such as a bucket, adapter, insert, bucket cover or rotor lid. A photo of the markings and the manual entry you’re comparing can save a round of correspondence.
Report the intended RCF in × g. If an older method gives only rpm, include the original rotor model and the documented radius used for any conversion. The same rpm produces different forces at different radii. You can see how force is reported in × g in sections 5.2–5.3 of the open-access guidance on serum and plasma handling.
Here’s a message you can adapt for the equipment manufacturer. Include the sentence about loaded mass if your rotor manual specifies a load limit.
Can you check whether [bottle part number] with [bottle cap part number] is supported in our [centrifuge and rotor models]? Our setup uses [applicable part numbers for the bucket, adapter, insert, bucket cover or rotor lid].
The bottle has a [flat, conical or other] base. The supplier lists a body OD of [ value ] mm and a capped height of [ value ] mm. The maximum width with the cap fitted is [value in mm or “not specified”]. I’ve attached the available drawing.
Our method calls for [ value ] × g at [ value ] °C with [ value ] mL per bottle. Our loaded mass is [ value ] g per [bucket or rotor bore], including [components specified in the rotor manual]. Could you identify the manual entry or provide written confirmation covering this combination and its operating limits?
Frequently Asked Questions
When a rotor manual says “with lid,” which lid does it mean?
Look for the component named in the heading or pictured beside the dimension. On a bottle drawing, the height may include the screw cap. A rotor table may give the available height under a bucket cover or rotor lid. In the 5910 R example, the aerosol-tight cap is the bucket cover. If your manual leaves the wording open, send the equipment manufacturer the page and the part numbers of the closures in question.
What if the bottle’s nominal diameter is exactly the adapter’s stated maximum?
For an exact bottle, closure and hardware combination listed by the equipment manufacturer, follow the conditions in that entry, including any clearance it specifies. If the manufacturer explicitly permits substitute bottles that meet dimensional criteria, check which feature the adapter limit covers. Compare it with the largest size the bottle drawing allows at that point. If the drawing gives only a nominal diameter equal to the limit, ask the bottle supplier for the tolerance. When the manual gives no criteria for substitutes, ask the equipment manufacturer to confirm your combination in writing.
The supplier changed the bottle part number. Does the old compatibility information still apply?
Ask for the supplier’s change notice or a written cross-reference. A different pack count can generate a new order number for the same bottle and cap. If the documentation explicitly identifies the same assembly under the new number, keep that record with the existing confirmation. A change to the bottle or cap calls for a fresh check against the rotor documentation.